Language: English Indonesia

EchothermTM Digital Hot Plates and Hot Plate/Stirrer model HP30 & HS30, Labtech LMS Series

(Product Photo) Models HP30 and HS30 EchoTherm Hot Plate/Stirrers Give the User: • Extremely easy use by anyone in your lab • Platinum RTD temperature measurement for precision and accuracy • Solid ceramic heater top for quick heating on a flat, white, chemically resistant surface. Milled flat cast aluminum top available on hot plate only model • Cast aluminum framed ceramic heater top edges stay cooler to prevent burns • PID temperature control for exact, tight sample control of plate or solution • Timer to 99 hours, 59 minutes, 59 seconds with settable Auto-Off for exactly timed sample preparation • Electronic calibration stored in chip. No batteries to replace. User calibratible • Temperature ramping for exact heating and cooling rates • Strong motor and magnet for stirring most samples • Full featured digital display for checking all parameters instantly • High and neutral lines fused for safety • UL, CSA, and CE certified Product Description: The EchoTherm HP30 and HS30 are products of years of experience in design, manufacturing, and marketing of digital hot plates and stirring hot plates. That experience was focused into the design of these units with the goal of making them the easiest to use and most accurate fully featured hot plates and stirring hot plates in the world. They are so simple to use it is surprising. Temperature measurement of a solution is accurate to 1% over the entire temperature range using a 100-ohm platinum RTD sensor and measurement system. Calibration of temperature is electronic and stored in memory. Calibration is set at the factory but can be done easily in the field using the probe calibration kit offered as an accessory. Heater tops are ceramic glass for all stirring hot plates and ceramic glass or milled flat cast aluminum for the hot plate only. The ceramic glass tops are a brilliant white flat glass set in a cast aluminum frame that are easy to clean and impervious to chemical spills. The ceramic glass is different than the cast plate with curved sides used by other manufacturers. These cast tops may have stress in them from the molding process and have been known to fracture when heated or put under stress by their mounting clips. The flat glass top of the Torrey Pines Scientific units eliminates this stress. Mounting them in a cast aluminum frame gives the additional advantage of a cool edge to the heating surface to help prevent accidental burns. The glass tops have efficient 600-watt heaters that can raise the plate surface temperature to 450°C in just a couple of minutes. The cast aluminum tops are flat to within 0.01 inches corner to corner and have 740-watt heaters that can raise the plate surface to 400°C in under ten minutes. The chassis on both models is cast aluminum designed to keep spills and heat out of the electronics. They are coated with chemically resistant epoxy based paint for durability. The membrane switch and display areas are covered with a replaceable, clear, soft vinyl cover to help keep spills off them. All units come complete with a six-foot long, three wire grounded, detachable line cord, fuse holder, and main ON-OFF switch. Both high and neutral lines are fused for safety. Product Specification: Hot Plate: Dimensions 8” (20.3 cm) x 8” (20.3 cm) Maximum temperature of the plate surface ceramic top: 450°C; cast aluminum top: 400°C Temperature control type PID Temperature accuracy 1% Temperature regulation, solution or plate ±1°C Heater power in watts ceramic top: 600W; aluminum top: 740W Temperature Measurement: Platinum RTD 100 ohm, in plate and in probe Range ceramic top: 0-450°C; aluminum top: 0-400°C Readability 1 °C Stirrer: Speed range unloaded 100 to 1500 rpm Readability 10 rpm Settability nearest 10 rpm Electrical: Available in 100, 115, and 230VAC, 50/60Hz Ceramic top 100 and 115VAC, 8 amp; 230VAC, 4 amp Aluminum top 100 and 115VAC, 10 amp; 230VAC, 5 amp Fusing Both high and neutral lines fused Line cord Detachable, 6 foot (1.8 meter), three-wire, grounded General: Dimensions, unpacked: Ceramic top 9.125" (23.18cm) side to side, 15.75" (40.01cm) front to back, 4.75" (12.07cm) high Aluminum top 9.125" (23.18cm) side to side, 15.75" (40.01cm) front to back, 5.00" (12.7cm) high Dimensions, packed Ceramic and aluminum tops 12.25" (31.12cm) by 18.25" (46.36cm) by 9.5" (24.13cm) Weight, unpacked Ceramic top 12 pounds (5.4kg) Aluminum top 13 pounds (5.9kg) Weight, packed Ceramic top 14 pounds (6.3kg) Aluminum top 15 pounds (6.8kg) Accessories Available: HS30-550 RS232, Factory installed HS30-600 Probe, Immersion, 6" stainless steel HS30-601 Probe, Immersion, 10" stainless steel HS30-602 Probe, Immersion, 6" solid Teflon HS30-603 Probe, Immersion, 6" solid glass HS30-700 Temperature Probe Calibration Kit Origin: United States Price: RFQ Quantity: 1 Pack. & Delivery: Unit Request for Quote Your inquiry will be recorded in "Member Trade Mail". Recommend to your friends